Hello, I am having some trouble with my Terratec Cinergy 400. After watching TV for a while with xawtv the picture disappears. The tuner and sound still work although changing channels takes longer than usual. The only way that I can get the card to work again is by cold-rebooting the computer. I've tried unloading and reloading all assiciated modules but it doesn't help. This is the module output (dmesg) when reloading saa7134 with modprobe after the picture has disappeared: Linux video capture interface: v1.00 i2c-core.o: i2c core module saa7130/34: v4l2 driver version 0.2.6 loaded PCI: Found IRQ 9 for device 00:09.0 saa7134[0]: found at 00:09.0, rev: 1, irq: 9, latency: 32, mmio: 0xe3001000 saa7134[0]: subsystem: 153b:1142, board: Terratec Cinergy 400 TV [card=8,insmod option] i2c-core.o: adapter saa7134[0] registered as adapter 0. saa7134[0]: i2c eeprom 00: 3b 15 42 11 ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff i2c-core.o: driver i2c TV tuner driver registered. tuner: probing saa7134[0] i2c adapter [id=0x90000] tuner: chip found @ 0xc0 tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) i2c-core.o: client [Philips PAL_BG (FI1216 and compa] registered to adapter [saa7134[0]](pos. 0). saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 Now when i run xawtv it says: This is xawtv-3.86, running on Linux/i686 (2.4.20) /dev/v4l/video0: ioctl VIDIOCSFBUF: Operation not permitted v4l-conf had some trouble, trying to continue anyway v4l2: WARNING: framebuffer base address mismatch v4l2: me=0xd8000000 v4l=(nil) ioctl: VIDIOC_DQBUF(index=0;type=VIDEO_CAPTURE;bytesused=0;flags=0x0 [];field=ANY;;timecode.type=0;timecode.flags=0;timecode.frames=0;timecode.seconds=0;timecode.minutes=0;timecode.hours=0;timecode.userbits="";sequence=0;memory=unknown): Input/output error And when i change channel with xawtv it says: v4l2: read: Input/output error v4l2: read: Input/output error ioctl: VIDIOC_DQBUF(index=0;type=VIDEO_CAPTURE;bytesused=0;flags=0x0 [];field=ANY;;timecode.type=0;timecode.flags=0;timecode.frames=0;timecode.seconds=0;timecode.minutes=0;timecode.hours=0;timecode.userbits="";sequence=0;memory=unknown): Input/output error I am using the following patches (against vanilla 2.4.20, but using newer i2c-modules) and packages: patch-2.4.20-kraxel.gz v4l2-20030207.tar.gz saa7134-20030218.tar.gz xawtv-20030304.tar.gz Any ideas? Is there any way of resetting the card via software to emulate a cold reboot? That would be a sufficient workaround for me. /Ludde -- _ _ _ __ __ ___ | | | | | \| \| __| Ludvig Omholt ................... ludde@xxxxxxxxx | |_| | | D | D | _| 073-055 02 13 ................. http://ludde.net/ |___|___|__/|__/|___| ++++++++ sauron: Linux 2.4.20 on an i686 ++++++++
Attachment:
pgp2USt4fw6ox.pgp
Description: PGP signature