Hello
Here are some feedback from the latest kernel: 2.4.21-pre5.
First after a reboot when i try xwatv for the first time as normal user
I get this printed in the shell and only a black picture:
xawtv
This is xawtv-3.74, running on Linux/i686 (2.4.21-pre5)
/dev/video0: ioctl VIDIOCSFBUF: Operation not permitted
v4l-conf had some trouble, trying to continue anyway
WARNING: v4l and dga disagree about the framebuffer base
WARNING: fbuf.base=(nil), dga=0xe8041000
WARNING: Is v4l-conf installed correctly?
WARNING: overlay mode disabled
Then if I start xawtv as normal user: xawtv -remote then it works
but the pictures are not updated so fast.
Then if I run xawtv as root thers is no problems at all.
And then if I start xawtv again as normal user, then xawtv
works ok but I get this printed in the shell:
xawtv
This is xawtv-3.74, running on Linux/i686 (2.4.21-pre5)
/dev/video0: ioctl VIDIOCSFBUF: Operation not permitted
v4l-conf had some trouble, trying to continue anyway
Kernel verion 2.4.20 did work without any problems,
and my bttv driver information from dmesg using the
the latest 2.4.21-pre5 kernel is like this:
btaudio: driver version 0.7 loaded [digital+analog]
btaudio: Bt878 (rev 17) at 00:0a.1, irq: 12, latency: 32, mmio: 0xeb001000
btaudio: using card config "default"
btaudio: registered device dsp2 [digital]
btaudio: registered device dsp3 [analog]
btaudio: registered device mixer1
Linux video capture interface: v1.00
i2c-core.o: driver i2c msp3400 driver registered.
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54
(PV951)
i2c-core.o: driver generic i2c audio driver registered.
i2c-core.o: driver i2c tda7432 driver registered.
i2c-core.o: driver i2c tda9875 driver registered.
i2c-core.o: driver i2c tda9887 driver registered.
i2c-core.o: driver i2c TV tuner driver registered.
i2c-core.o: driver tv card mixer driver registered.
SAA5249 driver (SAA5249 interface) for VideoText version 1.7
i2c-core.o: driver SAA5249 registered.
bttv: driver version 0.7.104 loaded
bttv: using 4 buffers with 2080k (8320k total) for capture
bttv: Host bridge is VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:0a.0, irq: 12, latency: 32, mmio: 0xeb000000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
msp34xx: init: chip=MSP3415D-B3 +nicam +simple
msp3410: daemon started
i2c-core.o: client [MSP3415D-B3] registered to adapter [bt848 #0](pos. 0).
tda9887: probing bt848 #0 i2c adapter [id=0x10005]
tuner: probing bt848 #0 i2c adapter [id=0x10005]
tuner: chip found @ 0xc2
i2c-core.o: client [(tuner unset)] registered to adapter [bt848 #0](pos. 1).
tvmixer: debug: MSP3415D-B3
tvmixer: MSP3415D-B3 (bt848 #0) registered with minor 32
tvmixer: debug: (tuner unset)
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: Hauppauge eeprom: model=44344, tuner=Philips FI1216 MK2 (5), radio=no
bttv0: using tuner=5
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: registered device video0
bttv0: registered device vbi0
And my graphics card is an STB LightSpeed 3300 (3Dfx Banshee) with
with the memery: 16384 kB.
Cheers Johnny
