Hey there... <( http://www.matthew2k.de.vu )>-=-<( powered by linux )> I have just tried the snapshot of the saa7134 module. First of all, as far as I can tell, there is a tuner type 5 on board... :) Now to the problem(s). I will start with the thing that drives me nuts -- it's that high tone in the background of the TV audio. I just figured that this does *only* occur when amux is set to TV instead of LINE2. Setting it to TV will also enable some kind of amplifying because the audio gets slowly amplified to a specific mark - with that high tone there from the beginning. Unfortunately if amux is set to LINE2, TV audio will *never* be anything else but mono --- with amux=TV, saa7134 will properably switch audio modes with that high tone though in the background. :( Also with LINE2 audio is activated as soon as the module is loaded and there is no way to switch it off except for muting the aux in the soundcard mixer itself, which shouldn't be necessary (again, this works fine with amux=TV: audio is only on if radio/tv is used). Nevertheless, the radio part always works fine in stereo in top quality without the annoying high tone... which is strange because TV and radio use same chip and the same tuner - so actually the tone should be here too. I have also talked to the Tevio support line to figure out if this high tone problem is known - and I was told they haven't heard of a thing like that yet, so probably this is caused by the saa7134 module somehow. Also the grabdisplay doesn't work yet. I get the following message: This is xawtv-3.73, running on Linux/i686 (2.4.19-pre8) v4l2: framebuffer info cap: clipping flags: extern base: 0xec000000 (nil) (nil) format: 1152x864, RGBP, 1990656 byte ioctl:VIDIOC_QBUF(0,type=1,off=0,len=221184,used=0,flags=0x0,ts=0,seq=0): Bad address ioctl: VIDIOC_QBUF(0,type=1,off=0,len=221184,used=0,flags=0x0,ts=0,seq=0): Bad address ioctl: VIDIOC_DQBUF(0,type=1,off=0,len=0,used=0,flags=0x0,ts=0,seq=0): Invalid argument What's also quite strange is that watching TV will destroy the text console, and I don't mean the problem when switching to the console while the overlay is still on - I mean start xawtv (either with or without Xv, makes no difference in this case), wait for the overlay, quit xawtv and take a look at the console - it's visually destroyed and stays that way until a program uses Xv for example... that will restore the text console. Also scaling with Xv doesn't work well too. The image looks like this... +++++++++++++++++++ + | N + + VIDEO | O + + OVERLAY | I + + | S + + | E + +++++++++++++++++++ With noise I mean just static garbage from the video memory. The picture is complete though... it's just not fully scaled in width. Last but not least one note to Gerd: I am sorry if you had the impression that I was angry at you for not answering in two seconds or so :)) - I never meant it that way... I know people are busy and have a real life, so I would never push anyone nor be impatient nor demand anything. So I am sorry if you got that wrong impression... :( Ok, I have also attached two debug outputs - one with amux:TV and one with amux:LINE2. Please let me know if I can help any further... So long, Matt -- ]) matthew2k@xxxxxx, GPG 0x51FA41C6, matthew2k on JABBER.org, ICQ# 89464954 ([
This is with amux:LINE2 - first I did some channel switching in xawtv and later on quit it and tried some radio... note, audio was *always on* and TV audio was always *mono* whereas the radio out was still stereo. May 6 15:31:43 kernel: saa7130/34: v4l2 driver version 0.1.6 loaded May 6 15:31:43 kernel: PCI: Found IRQ 11 for device 00:09.0 May 6 15:31:43 kernel: saa7134[0]: found at 00:09.0, rev: 1, irq: 11, latency: 24, mmio: 0xef001000 May 6 15:31:43 kernel: saa7134[0]: subsystem: 1131:0000, board: Tevion MD 9717 May 6 15:31:43 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:31:43 kernel: saa7134[0]: Huh, no eeprom present (err=-5)? May 6 15:31:43 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:31:43 kernel: saa7134[0]/audio: tvaudio thread scan start [0] May 6 15:31:43 kernel: tuner: probing saa7134[0] i2c adapter [id=0x90000] May 6 15:31:43 kernel: tuner: chip found @ 0xc0 May 6 15:31:43 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:31:43 kernel: saa7134[0]: registered device video0 [???] May 6 15:31:43 kernel: saa7134[0]: registered device vbi0 May 6 15:31:43 kernel: saa7134[0]: registered device radio0 May 6 15:31:43 kernel: saa7134[0]: registered device dsp0 May 6 15:31:43 kernel: saa7134[0]: registered device mixer0 May 6 15:31:44 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 13 [84/97] May 6 15:31:44 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 3738 [2314/-1424] May 6 15:31:45 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 527 [-86/441] May 6 15:31:45 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 6.000 MHz May 6 15:31:45 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-I NICAM [6.000/6.552 MHz] May 6 15:31:46 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-I NICAM [6.000/6.552 MHz] May 6 15:31:47 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:47 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:31:47 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:47 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:47 kernel: saa7134[0]/audio: tvaudio thread scan start [1] May 6 15:31:47 kernel: saa7134[0]/audio: ctl_mute=0 automute=1 input=Television => mute=1 input=Television May 6 15:31:47 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:47 kernel: saa7134[0]/audio: tvaudio thread scan start [2] May 6 15:31:48 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 6582 [3663/10245] May 6 15:31:48 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 13196 [14131/935] May 6 15:31:49 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 126 [-742/-616] May 6 15:31:49 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:49 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 6.000 MHz May 6 15:31:49 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-I NICAM [6.000/6.552 MHz] May 6 15:31:50 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-I NICAM [6.000/6.552 MHz] May 6 15:31:50 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:31:50 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:50 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:50 kernel: saa7134[0]/audio: tvaudio thread scan start [3] May 6 15:31:50 kernel: saa7134[0]/audio: ctl_mute=0 automute=1 input=Television => mute=1 input=Television May 6 15:31:50 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:50 kernel: saa7134[0]/audio: tvaudio thread scan start [4] May 6 15:31:51 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 27434 [-13550/13884] May 6 15:31:51 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 200 [-516/-716] May 6 15:31:52 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 27 [-61/-88] May 6 15:31:52 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:52 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:31:52 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:31:53 kernel: saa7134[0]/audio: found audio subchannels: mono May 6 15:31:53 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:31:54 kernel: saa7134[0]/audio: found audio subchannels: mono May 6 15:31:54 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:31:54 kernel: saa7134[0]/audio: found audio subchannels: mono May 6 15:31:54 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:54 kernel: saa7134[0]/audio: tvaudio thread scan start [5] May 6 15:31:54 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:54 kernel: saa7134[0]/audio: tvaudio thread scan start [6] May 6 15:31:55 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 24274 [-11538/12736] May 6 15:31:55 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 1323 [1291/-32] May 6 15:31:55 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 231 [-174/-405] May 6 15:31:55 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:31:55 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:31:55 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:31:56 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:31:56 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:31:58 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:31:58 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:31:58 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:31:58 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:58 kernel: saa7134[0]/audio: tvaudio thread scan start [7] May 6 15:31:58 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:31:58 kernel: saa7134[0]/audio: tvaudio thread scan start [8] May 6 15:31:59 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 26594 [-11536/15058] May 6 15:31:59 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 1921 [1424/-497] May 6 15:32:00 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 680 [-195/-875] May 6 15:32:00 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:32:00 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:32:00 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:32:01 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:32:01 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:32:04 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:32:06 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:32:06 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:32:06 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:32:08 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:08 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:08 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:32:08 kernel: saa7134[0]/audio: tvaudio thread scan start [9] May 6 15:32:08 kernel: saa7134[0]/audio: ctl_mute=0 automute=1 input=Radio => mute=1 input=Radio May 6 15:32:09 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:32:09 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 1062 [-1464/-2526] May 6 15:32:10 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 6573 [552/-6021] May 6 15:32:10 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 700 [1692/992] May 6 15:32:10 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:10 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 6.000 MHz May 6 15:32:10 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-I NICAM [6.000/6.552 MHz] May 6 15:32:11 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-I NICAM [6.000/6.552 MHz] May 6 15:32:13 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:13 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:14 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:14 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:15 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:15 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:16 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:16 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:17 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:32:18 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:32:21 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio
This is with amux:TV - first I did some channel switching in xawtv and later on quit it and tried some radio... this only works if the computer has been coldstarted (no warmstart) previously otherwise you get no TV audio (except for the radio trick I reported earlier). And there is this high tone in this seemingly aplified TV audio... nevertheless, radio output is still clear and just fine. May 6 15:27:08 kernel: saa7130/34: v4l2 driver version 0.1.6 loaded May 6 15:27:08 kernel: PCI: Found IRQ 11 for device 00:09.0 May 6 15:27:08 kernel: saa7134[0]: found at 00:09.0, rev: 1, irq: 11, latency: 24, mmio: 0xef001000 May 6 15:27:08 kernel: saa7134[0]: subsystem: 1131:0000, board: Tevion MD 9717 May 6 15:27:08 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:27:08 kernel: saa7134[0]: Huh, no eeprom present (err=-5)? May 6 15:27:08 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:27:08 kernel: saa7134[0]/audio: tvaudio thread scan start [0] May 6 15:27:08 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:27:08 kernel: tuner: probing saa7134[0] i2c adapter [id=0x90000] May 6 15:27:08 kernel: tuner: chip found @ 0xc0 May 6 15:27:08 kernel: saa7134[0]: registered device video0 [???] May 6 15:27:08 kernel: saa7134[0]: registered device vbi0 May 6 15:27:08 kernel: saa7134[0]: registered device radio0 May 6 15:27:08 kernel: saa7134[0]: registered device dsp0 May 6 15:27:08 kernel: saa7134[0]: registered device mixer0 May 6 15:27:08 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:27:08 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:27:09 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 28623 [-13937/14686] May 6 15:27:09 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 3578 [2382/-1196] May 6 15:27:10 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 1701 [-463/1238] May 6 15:27:10 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:27:10 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:11 kernel: saa7134[0]/audio: found audio subchannels: mono May 6 15:27:11 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:13 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:13 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:27:13 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:13 last message repeated 3 times May 6 15:27:13 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:27:13 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:13 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:13 kernel: saa7134[0]/audio: tvaudio thread scan start [1] May 6 15:27:14 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:14 kernel: saa7134[0]/audio: tvaudio thread scan start [2] May 6 15:27:15 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 28133 [-13436/14697] May 6 15:27:15 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 754 [1290/536] May 6 15:27:15 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 79 [-323/-244] May 6 15:27:15 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:27:15 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:27:15 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:16 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:16 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:19 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:20 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:20 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:27:20 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:20 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:20 kernel: saa7134[0]/audio: tvaudio thread scan start [3] May 6 15:27:21 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:21 kernel: saa7134[0]/audio: tvaudio thread scan start [4] May 6 15:27:22 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 14182 [-8999/5183] May 6 15:27:22 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 788 [187/-601] May 6 15:27:22 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 352 [-134/-486] May 6 15:27:22 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:27:22 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:27:22 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:23 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:23 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:26 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:30 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:30 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:27:30 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:30 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:30 kernel: saa7134[0]/audio: tvaudio thread scan start [5] May 6 15:27:31 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:31 kernel: saa7134[0]/audio: tvaudio thread scan start [6] May 6 15:27:32 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 12537 [-9040/3497] May 6 15:27:32 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 141 [-10/131] May 6 15:27:32 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 292 [-446/-738] May 6 15:27:32 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0 input=Television May 6 15:27:32 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 5.500 MHz May 6 15:27:32 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:33 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:33 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-B/G FM-stereo [5.500/5.742 MHz] May 6 15:27:36 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:43 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:43 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1 input=Television May 6 15:27:43 kernel: saa7134[0]/audio: found audio subchannels: mono stereo May 6 15:27:46 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:46 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:46 kernel: saa7134[0]/video: DCSDT: found PAL May 6 15:27:46 kernel: saa7134[0]/audio: tvaudio thread scan start [7] May 6 15:27:46 kernel: saa7134[0]/audio: ctl_mute=0 automute=1 input=Radio => mute=1 input=Radio May 6 15:27:46 kernel: saa7134[0]/video: DCSDT: no signal May 6 15:27:47 kernel: saa7134[0]/audio: scanning 5.500 MHz => dc is 1259 [-3234/-1975] May 6 15:27:47 kernel: saa7134[0]/audio: scanning 6.000 MHz => dc is 1580 [1869/289] May 6 15:27:47 kernel: saa7134[0]/audio: scanning 6.500 MHz => dc is 3542 [-1191/2351] May 6 15:27:47 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:47 kernel: saa7134[0]/audio: found PAL-BGHI main sound carrier @ 6.500 MHz May 6 15:27:47 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-D/K1 FM-stereo [6.500/6.258 MHz] May 6 15:27:48 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-D/K2 FM-stereo [6.500/6.742 MHz] May 6 15:27:49 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-D/K3 FM-stereo [6.500/5.742 MHz] May 6 15:27:50 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:50 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:50 kernel: saa7134[0]/audio: tvaudio_setmode: trying PAL-D/K NICAM [6.500/5.850 MHz] May 6 15:27:50 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:51 kernel: saa7134[0]/audio: tvaudio_setmode: using PAL-D/K1 FM-stereo [6.500/6.258 MHz] May 6 15:27:51 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:52 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:52 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:53 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:53 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:54 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio May 6 15:27:54 kernel: saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0 input=Radio May 6 15:27:58 kernel: saa7134[0]/audio: ctl_mute=1 automute=0 input=Radio => mute=1 input=Radio
