Hi All - this is my first post. I have a problem being able to tune any NTSC us-cable channels using the Hauppage PVR-250. I've got pretty much everything installed from the install docs. I use tuner type=2 and the ivtv driver from the 7/7/2003 CVS snapshot. The driver runs well, except that I can't get it tune into any of the channels correctly - all I get is the static with sound. I've played around with changing frequencies with ptune.pl and ptune-ui.pl and I do seem to be picking up a few channels just by going through all frequencies and figure out what channel i'm getting. But doing this for all 70+ channels is very tough. Is there something I'm doing wrong? I would assume that us-cable freqtable and everything to be stable, but I'm not sure as this is only my second week at this stuff. I was going through the mail archives here to see if there's any answers. The closest issue I found was this below. However, I do not see any resolution. I too have the same exact info listed from lspci: 03:06.0 Multimedia video controller: Internext Compression Inc: Unknown device 0016 (rev 01) Subsystem: Hauppauge computer works Inc.: Unknown device 4009 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (32000ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- I also tried switching channels from mythtv, but get the same results. Furthermore, I tried changing the tuner type= setting to several different types. The closest I get is using type=3 (PAL). Using this I get most of my channels, but they all are off by 1 (if setting channel 6, you're actually watching channel 5). But from reading several docs, all seem to conclude that I have set the wrong tuner type (which is obvious since I need to use NTSC). So I'm back to trying with tuner type=2. Here's some info I've pulled off the card if that helps: # Hauppage PVR 250: NTSC 32021 Rev B210 # I have: Philips Tuner # 3139 147 132 61A # FI1236 MK2/F hm # SV23 0249 # Phillips Chip: # SAA7115 ML # C88347 # TS0306-1 # Conexant MPEG II A/V Encoder Chip: # CX23416-12 # E304424.1 # 0249 Taiwan Any help will be greatly appreciated! Thanks, Shailesh ===================================================== I'm trying to use this with MythTV, so I was using mythtv to change channels. I had also tried ptune.pl to change channels with no luck (it appeared to change the channels without error, but I get the same results from cat /dev/video0 > /tmpfile or myth). As for output from dmesg, I'm not sure offhand, I'll check when I get home. Also, I'm in the US. Thank you, Robert Jacobson -----Original Message----- From: ivtv-devel-admin@xxxxxxxxxxxxxxxxxxxxx [mailto:ivtv-devel-admin@xxxxxxxxxxxxxxxxxxxxx] On Behalf Of kevin thayer Sent: Friday, June 20, 2003 4:40 PM To: ivtv-devel@xxxxxxxxxxxxxxxxxxxxx Subject: Re: [ivtv-devel] PVR250 tuner problems > the cat > /dev/video0 test fine using the s-video > input. However, when > I try to watch tv, all I get is static. I've tried > many of the tuner's have you used ptune.pl or one of the other programs in util/ to change the channel? > to show, but when I try to change channels, nothing > happens. Also, I how are you trying to change channels? what output is given to dmesg when you change channels? Where are you in the world? > However, with the new CVS, when I try to compile the > utils, this is what > I get: I updated cvs last night with the changes that will fix this. Sourceforge is about a day behind due to their new replication policy. (changes put in cvs arent' downloadable anonymously for ~24hrs) Keep trying, it will eventually compile. -tmk __________________________________ Do you Yahoo!? SBC Yahoo! DSL - Now only $29.95 per month! http://sbc.yahoo.com ------------------------------------------------------- This SF.Net email is sponsored by: INetU Attention Web Developers & Consultants: Become An INetU Hosting Partner. Refer Dedicated Servers. We Manage Them. You Get 10% Monthly Commission! INetU Dedicated Managed Hosting http://www.inetu.net/partner/index.php _______________________________________________ ivtv-devel mailing list ivtv-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.sourceforge.net/lists/listinfo/ivtv-devel ------------------------------------------------------- This SF.Net email is sponsored by: INetU Attention Web Developers & Consultants: Become An INetU Hosting Partner. Refer Dedicated Servers. We Manage Them. You Get 10% Monthly Commission! INetU Dedicated Managed Hosting http://www.inetu.net/partner/index.php _______________________________________________ ivtv-devel mailing list ivtv-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.sourceforge.net/lists/listinfo/ivtv-devel _______________________________________________ No banners. No pop-ups. No kidding. Introducing My Way - http://www.myway.com