Hi,
Yeah, I was remembering this discussion as Stane first mentioned it a
couple of days ago. I went through and trimmed out a few of the
original responses that were used when putting this table together:
--------------------------------------------
Robert (me):
Yes, my Flyvideo 3000 card includes FM tuner and Remote control:
(aa7134hl, hef4052bt, lva001, pll24, pll4, Tuner: TCL2002MB-1F)
I have had a look at the hardware of my card, the PCB is labelled LA158
Rev C. It has a TCL2002(S?)MB-1 tuner (I thought it said had S in there
when I looked, but reading your emails has confused me....). I have
remote control and the chip LVA001 (but I haven't actually got it
working yet - is it supported or is there tricks I have to do?).
I also have the HEF-4052BT chip. I do not have FM, and there is a
footprint on the board for the chips SBX1673 or SBX1637, but this is not
populated.
--------------------------------------------
Gunther:
My FV3K (w/FM w/IR Tuner:TCL2002MB-1F) has:
saa7130/34: v4l2 driver version 0.1.5 loaded
saa7134[0]: found at 00:11.0, rev: 1, irq: 5, latency: 32, mmio: 0xe4000000
saa7134[0]: subsystem: 1131:0000, board: LifeView FlyVIDEO3000
saa7134 initial gpio_mode = 00000000
saa7134: initial gpio_state = 00031000
Here PHILIPS_PAL(tuner=5) works fine.
--------------------------------------------
TC:
Phillips SAA7130 based, mono audio decoding only, no FM radio option.
Audio out fed into the Soundcard (SBLive 128) Audio Input jack.
The PCB has version LR 138 Rev. C
Tuner block: PAL B/G standard, containing
Phillips TDA9800T
Phillips TDA6503AT
(I opened the metal shield casing to check this)
Other additional ICs (on PCI board):
Phillips HEF4052BT C5917ME (16 pin)
<Unknown> LVA001 0028GC41 (18 pin)
Output from lspci -vv for the card:
00:09.0 Multimedia controller: Philips Semiconductors: Unknown device 7130
(rev 01)
Subsystem: Philips Semiconductors: Unknown device 0000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e1001000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Regards,
Rob
Wan Tat Chee wrote:
I found this file which I've compiled during the time I was tearing my
hair out with the FV2K. Maybe it'll be the basis for a template.
(I forgot about it until someone asked about the FV2K+FM issue).
HTH,
T.C.
On Fri, 18 Oct 2002, David Antliff wrote:
My hope is that it will become a step forward to working out what the
problem is - because patterns should become apparent, provided the survey
is properly designed. A survey with carefully designed questions will
also
help to eliminate the misunderstanding and lack of consistent information
common with a descriptive email.
Please let me know if my idea sounds useful, and if you'd like to help.
Suggestions for info to be mentioned in the survey is welcome.
----
Wan Tat Chee (Lecturer)
School of Computer Science, Univ. Science Malaysia,
11800 Minden, Penang, Malaysia. Ofc Ph: +604 657-7888 x 3617
Internet: tcwan@xxxxxxxxx Web: http://nrg.cs.usm.my/~tcwan
GPG Key : http://nrg.cs.usm.my/~tcwan/tcw_gpg.asc
F'print : FB0F CED7 85A5 ECF9 DEF0 50E8 A550 A0D2 8638 B1EB
------------------------------------------------------------------------
Gunther, Robert, et al,
This is a summary of the different FlyVideo specs discussed so far. I
don't think the
remote option affects the normal operation, so I've ignored it in the
specs for now.
Blanks indicate missing info. Please post corrections as necessary.
I have the LVA001 IC, but I don't have the remote control. It doesn't
have any manufacturer markings.
I have unpopulated IC pads on my FV2K board for QFP-style ICs.
I consistently get a "eeprom read error #1 rc=-5", this is normal as
FlyVideo is being cheap
and not including an EEPROM on board.
General Specs
=============
Board Revision TV Norm Tuner saa7134 TV Tuner Type Init.GPIO Ext.AMux
-------------------------------------------------------------------------------------------------------
FV2K LR 138 Rev. C PAL-BG TCL2002MB-1 TUNER_LG_PAL_NEW_TAPC (37)
00030500 Yes
FV3K LA 158 Rev. C PAL-BG(?) TCL2002MB-1 TUNER_LG_PAL_NEW_TAPC (37) Yes
FV3K+FM+Rem TCL2002MB-1F TUNER_PHILIPS_PAL (5) 00031000 Yes
Notes:
Init.GPIO: Initial GPIO Status. Mask with 0x6000 as the two bits are
used for controlling the external
HEF4052BT analog mux
FV2K uses SAA7130, FV3K uses SAA7134.
1. FV2K -- TC Wan
2. FV3K -- Robert Reid
3. FV3K+FM+Rem -- Gunther Mayer
Input Selection
===============
Board TV.Vmux TV.Amux Comp.Vmux S-Vid.Vmux Ext.Amux Radio.Amux
------------------------------------------------------------------------------------
FV2K 1 LINE2+0x0000 3 8 LINE2+0x4000 --
FV3K 1 TV
FV3K+FM+Rem 1 TV 3 6 (?) LINE2+0x4000 LINE2+0x0000
