Hi Roger, Have you tried xawtv version 3.68? xawtv version 3.69 (and 3.70) also crash with me with the bttv driver (version 0.7.x) I use at home. xawtv version 3.68 works without any problems in my configuration. At work I use an xawtv version 3.65 with the SAA7134 driver without any problems Gert "Roger W.Brown" wrote: > > Hi, > > I have failed to make SAA7134 to work and would be grateful for > any suggestions. The steps thus far are: > > Linux-2.4.18-pre8 was patched with: > 10_videodev-2.4.18-pre8.diff > 11_v4l2-2.4.18-pre8.diff > 15_pci-2.4.18-pre8.diff > > The kernel was configured with: I2C, I2C bit-banging > Phillips style parallel port adapter, I2C device interface and > I2C /proc interface. > > Devfs is in operation (this may be the problem) and V4L2 backward > compatability. > > saa7134-20020205 was built and inatalled as well as xawtv-3.69 > > Various boot and module loading messages are: > > i2c-core.o: i2c core module > i2c-dev.o: i2c /dev entries driver module > i2c-core.o: driver i2c-dev dummy driver registered. > i2c-algo-bit.o: i2c bit algorithm module > i2c-philips-par.o: i2c Philips parallel port adapter module > i2c-philips-par.o: attaching to parport0 > i2c-dev.o: Registered 'Philips Parallel port adapter' as minor 0 > i2c-core.o: adapter Philips Parallel port adapter registered as adapter 0. > i2c-proc.o version 2.6.1 (20010825) > > eth0: Digital DS21140 Tulip rev 34 at 0xec00, 00:C0:F0:30:DA:1B, IRQ 11. > Linux video capture interface: v1.00 > V4L2: v4l1 backward compatibility enabled. > SAA5249 driver (SAA5249 interface) for VideoText version 1.7 > i2c-core.o: driver SAA5249 registered. > i2c-core.o: driver sab3036 registered. > tuner: SAB3036 found, status 00 > i2c-core.o: client [SAB3036] registered to adapter [Philips Parallel port adapter](pos. 0). > Linux agpgart interface v0.99 (c) Jeff Hartmann > > argo kernel: i2c-core.o: driver i2c TV tuner driver registered. > argo kernel: tuner: ignoring Philips Parallel port adapter i2c adapter [id=0x10000] > argo kernel: saa7130/34: v4l2 driver version 0.1.5 loaded > argo kernel: saa7134[0]: found at 00:0f.0, rev: 1, irq: 9, latency: 64, mmio: 0xfebfec00 > argo kernel: saa7134[0]: subsystem: 1131:0000, board: LifeView FlyVIDEO3000 > argo kernel: i2c-dev.o: Registered 'saa7134[0]' as minor 1 > argo kernel: tuner: probing saa7134[0] i2c adapter [id=0x90000] > argo kernel: saa7134[0]/video: DCSDT: no signal > argo kernel: tuner: chip found @ 0xc2 > argo kernel: i2c-core.o: client [Philips PAL] registered to adapter [saa7134[0]](pos. 0). > argo kernel: i2c-core.o: adapter saa7134[0] registered as adapter 1. > argo kernel: saa7134[0]: i2c eeprom read error #1 rc=-5 > argo kernel: devfs_register(v4l/video0): could not append to parent, err: -17 > argo kernel: saa7134[0]: registered device video0 > argo kernel: saa7134[0]: registered device vbi0 > argo kernel: saa7134[0]: registered device radio0 > argo kernel: saa7134[0]: registered device dsp2 > argo kernel: saa7134[0]: registered device mixer1 > argo kernel: saa7134[0]/video: DCSDT: no signal > > I have a FlyVideo-3000 card installed and all modules are installed by > hand. Before testing, lsmod shows: > > Module Size Used by > saa7134 45120 0 (unused) > tuner 8192 1 > video-mm 3472 0 [saa7134] > emu10k1 54048 0 (unused) > ac97_codec 9408 0 [emu10k1] > sound 53984 0 (unused) > soundcore 3472 8 [saa7134 emu10k1 sound] > > and xawtv -hwscan gives: > > This is xawtv-3.69, running on Linux/i686 (2.4.18-pre8) > looking for available devices > port 67-67 > type : Xvideo, image scaler > name : Matrox G-Series Backend Scaler > > /dev/v4l/video0: OK [ -device /dev/v4l/video0 ] > type : v4l2 > name : saa7134[0] > flags: overlay capture tuner > > A simple xawtv command produces: > > This is xawtv-3.69, running on Linux/i686 (2.4.18-pre8) > v4l2: framebuffer info > cap: clipping > flags: > base: 0xf2000000 (nil) (nil) > format: 1200x900, BGR4, 4377600 byte > v4l2: WARNING: framebuffer bpl mismatch > v4l2: me=4864 v4l=4800 > Segmentation fault > > and any attempt to gain further information via strace or gdb > on an unstripped xawtv executable, freezes the system ! > > Thanks in advance, > > Roger Brown > > _______________________________________________ > Video4linux-list mailing list > Video4linux-list@xxxxxxxxxx > https://listman.redhat.com/mailman/listinfo/video4linux-list
