Hi, I have a WinTV GO card which works without any problems with bttv2, but when I load a bttv 0.7.x or 0.8.x I don't get any sound out of that card. The picture is there, I also tried to unmute and control the volume settings without any success. (Of course there's a cable between the line-out of the wintv and line-in of the soundcard) I found some threads about the "no sound problem" when searching the archives, but found no solution so far. As the WinTV Go is a quite popular card I think it is already supported, so the error sits in front of the monitor ;) (RTFMs appreciated) Some info: Kernel: 2.4.13-ac6 (v4l2 and videodevX) Audio: kernel oss drivers (mad16) ___ eeprom -x PCI Vendor ID: 0x0070, Subsystem ID: 0x13eb Decoding Hauppauge EEPROM: Model : 44004 Revision : B129 Serial : 2233242 Tuner : Temic 4006FH5 Tuner Formats: PAL(B/G) Audio : None Audio Outputs: BackPanel Decoder : BT878 Video Formats: NTSC(M) PAL(BGHIDK) SECAM(L/L´) PAL(M) PAL(N) NTSC(443) PAL(NCOMBO) Videotext : Yes (Software) Radio : no Infrared : no Checksum : 79 [OK] EEPROM: 84 12 00 00 05 50 0e 7f 04 1d 01 e4 ab 99 14 89 00 00 00 00 00 84 0a 00 01 01 20 77 00 40 9a 13 22 00 74 02 01 00 02 79 79 ___ lsmod (with non-working bttv 0.7/0.8) Module Size Used by Tainted: P tuner 4484 1 (autoclean) tvaudio 8000 0 (autoclean) (unused) bttv 70976 0 (autoclean) (unused) video-mm 2180 0 (autoclean) [bttv] i2c-algo-bit 6956 1 (autoclean) [bttv] videodev1.o.old 5504 2 (autoclean) [bttv] v4l2-common 4664 0 (autoclean) [bttv] i2c-dev 3488 0 (autoclean) i2c-core 12736 0 (autoclean) [tuner tvaudio bttv i2c-algo-bit i2c-dev] mad16 7360 0 (autoclean) ad1848 16352 0 (autoclean) [mad16] uart401 6048 0 (autoclean) [mad16] sound 52652 0 (autoclean) [mad16 ad1848 uart401] soundcore 3460 5 (autoclean) [sound] rtc 5240 1 (autoclean) ___ syslog messages: kernel: Linux video capture interface: v1.00 kernel: i2c-algo-bit.o: i2c bit algorithm module version 2.6.1 (20010830) kernel: bttv: driver version 0.8.30 loaded [v4l/v4l2] kernel: bttv: using 32 buffers with 2080k (520 pages) each for capture kernel: bttv: Host bridge is VIA Technologies, Inc. VT82C598 [Apollo MVP3] kernel: bttv: Host bridge is VIA Technologies, Inc. VT82C586B ACPI kernel: bttv: Host bridge needs ETBF enabled. kernel: bttv: Host bridge needs VSFX enabled. kernel: bttv: Bt8xx card found (0). kernel: PCI: Found IRQ 4 for device 00:0b.0 kernel: PCI: Sharing IRQ 4 with 00:0b.1 kernel: bttv0: Bt878 (rev 17) at 00:0b.0, irq: 4, latency: 32, memory: 0xeb001000 kernel: bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb kernel: bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected] kernel: bttv0: enabling ETBF (430FX/VP3 compatibilty) kernel: bttv0: enabling VSFX kernel: bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] kernel: i2c-algo-bit.o: Adapter: bt848 #0 scl: 1 sda: 1 -- testing... kernel: i2c-algo-bit.o:1 scl: 1 sda: 0 kernel: i2c-algo-bit.o:2 scl: 1 sda: 1 kernel: i2c-algo-bit.o:3 scl: 0 sda: 1 kernel: i2c-algo-bit.o:4 scl: 1 sda: 1 kernel: i2c-algo-bit.o: bt848 #0 passed test. kernel: i2c-algo-bit.o: scanning bus bt848 #0. kernel: ................................................................................(50)....... ................ kernel: i2c-dev.o: Registered 'bt848 #0' as minor 0 kernel: i2c-core.o: adapter bt848 #0 registered as adapter 0. kernel: bttv0: Hauppauge eeprom: model=44004, tuner=Temic 4006FH5 (14), radio=no kernel: bttv0: i2c: checking for MSP34xx @ 0x80... not found kernel: bttv0: i2c: checking for TDA9875 @ 0xb0... not found kernel: bttv0: i2c: checking for TDA7432 @ 0x8a... not found kernel: tvaudio: TV audio decoder + audio/video mux driver kernel: tvaudio: known chips: tda9840,tda9873h,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV 951) kernel: i2c-core.o: driver generic i2c audio driver registered. kernel: i2c-core.o: driver i2c TV tuner driver registered. kernel: tuner: chip found @ 0xc2 kernel: bttv0: i2c attach [client=Temic PAL_I (4006FH5),ok] kernel: i2c-core.o: client [Temic PAL_I (4006FH5)] registered to adapter [bt848 #0](pos. 0). kernel: bttv0: PLL: 28636363 => 35468950 .. ok This problem isn't too dramatic as I have a working configuration, but I heard somewhere, that the bttv2 driver will not be continued, so I'd like to have a configuration that still works in the future... Thanks in advance, Dirk
