folks, i have recently installed a hauppage wintv-d card and unfortunately have not been able to get the thing to work. i am currently just trying to use the analog cable-tv signal. using xawtv seems to yield nothing but noise. your help/advise would be greatly appreciated. i have tried to read all the howtos and fms, but will followup on any leads provided. following are the details: 1. using debian 2.2 2. kernel 2.2.18pre21 3. i2c-2.5.5 patch applied to kernel per instructions in i2c-2.5.5/INSTALL for option #3 ([patching kernel). 4. installed bttv-0.7.63 src to ~me/bttv-0.7.63 built it and installed as kernel modules, overwriting the defaults bundled with the 2.2 kernel. 5. inserted modules: a. without "type" arg to tuner, tuner not found (tuner type 4): kernel: i2c-core.o: driver i2c TV tuner driver registered. kernel: bttv: driver version 0.7.63 loaded kernel: bttv: using 2 buffers with 2080k (4160k total) for capture kernel: bttv: Host bridge: 82441FX Natoma, bufcon=0xef kernel: bttv: Bt8xx card found (0). kernel: bttv0: Bt878 (rev 17) at 00:0a.0, irq: 11, latency: 32,memory: 0xe1120000 kernel: bttv0: subsystem: 0070:3900 => Hauppauge WinTV-D =>card=10 kernel: bttv0: model: BT878(Hauppauge new (bt878)) [autodetected] kernel: PCI: Enabling bus mastering for device 00:50 kernel: bttv0: Hauppauge msp34xx: reset line init kernel: msp34xx: init: chip=MSP3438G-A1, has NICAM support kernel: msp3410: daemon started kernel: bttv0: i2c attach [MSP3438G-A1] kernel: i2c-core.o: client [MSP3438G-A1] registered to adapter [bt848#0](pos. 0). kernel: tuner: chip found @ 0x61 kernel: bttv0: i2c attach [(unset)] kernel: i2c-core.o: client [(unset)] registered to adapter [bt848#0](pos. 1). kernel: i2c-core.o: adapter bt848 #0 registered as adapter 0. kernel: bttv0: Hauppauge eeprom: model=39000, tuner=Philips TD1536D(4), radio=no Apr 17 02:41:39 Linux kernel: tuner: type set to 4 (NoTuner) kernel: bttv0: i2c: checking for MSP34xx @ 0x80... found kernel: bttv0: i2c: checking for TDA9875 @ 0xb0... not found kernel: bttv0: i2c: checking for TDA7432 @ 0x8a... not found b. with "type" arg to tuner: kernel: i2c-core.o: driver i2c TV tuner driver registered. kernel: bttv: driver version 0.7.63 loaded kernel: bttv: using 2 buffers with 2080k (4160k total) for capture kernel: bttv: Host bridge: 82441FX Natoma, bufcon=0xef kernel: bttv: Bt8xx card found (0). kernel: bttv0: Bt878 (rev 17) at 00:0a.0, irq: 11, latency: 32,memory: 0xe1120000 kernel: bttv0: subsystem: 0070:3900 => Hauppauge WinTV-D =>card=10 kernel: bttv0: model: BT878(Hauppauge new (bt878)) [autodetected] kernel: PCI: Enabling bus mastering for device 00:50 kernel: bttv0: Hauppauge msp34xx: reset line init kernel: msp34xx: init: chip=MSP3438G-A1, has NICAM support kernel: msp3410: daemon started kernel: bttv0: i2c attach [MSP3438G-A1] kernel: i2c-core.o: client [MSP3438G-A1] registered to adapter [bt848#0](pos. 0). kernel: tuner: chip found @ 0x61 kernel: bttv0: i2c attach [Philips NTSC] kernel: i2c-core.o: client [Philips NTSC] registered to adapter [bt848#0](pos. 1). kernel: i2c-core.o: adapter bt848 #0 registered as adapter 0. kernel: bttv0: Hauppauge eeprom: model=39000, tuner=Philips TD1536D(4), radio=no kernel: bttv0: i2c: checking for MSP34xx @ 0x80... found kernel: bttv0: i2c: checking for TDA9875 @ 0xb0... not found kernel: bttv0: i2c: checking for TDA7432 @ 0x8a... not found 6. lsmod: Module Size Used by bttv 53108 0 (unused) tuner 4336 1 tvaudio 7756 0 (autoclean) (unused) msp3400 13600 1 (autoclean) kcompat24 3840 0 [bttv tvaudio msp3400] i2c-algo-bit 7028 1 [bttv] i2c-core 12540 0 [bttv tuner tvaudio msp3400i2c-algo-bit] tia, <daryl/>
