Wan Tat Chee schrieb:
Hello,
> > > option tuner type=37 (FlyVideo 3000 you have other card)
> >
> > I have a FlyVIDEO3000 stereo + FM, but it isn't on the list.
>
> I believe that the FlyVideo 3000 entry is for your config. If you take a
> look at the saa7134-cards.c file, you'll see that FM is defined.
option tuner type=37 brings snow noise on xawtv without any acoustics.
> Also, the Recording input should be set to LINE in and
> unmuted. This is a typical problem that shows up where xawtv doesn't
> have any sound initially then after running aumix, it works.
I use the SB-Live line input with output from my Hifi-amp long time
bevore I use TV on the PC, it works well in time.
> After that, if audio still doesn't work, see if 'debug_audio=1' for
> saa7134 gives you any info on audio detection (dmesg |fgrep saa7134).
# dmesg |fgrep saa7134
saa7134[0]: found at 02:0d.0, rev: 1, irq: 9, latency: 32, mmio:
0xed000000
saa7134[0]: subsystem: 1131:0000, board: LifeView FlyVIDEO3000
saa7134[0]/audio: ctl_mute=1 automute=0 input=Television => mute=1
input=Television
i2c-core.o: adapter saa7134[0] registered as adapter 0.
saa7134[0]/audio: tvaudio thread scan start [0]
saa7134[0]: Huh, no eeprom present (err=-5)?
saa7134[0]/video: DCSDT: no signal
saa7134[0]/video: DCSDT: no signal
tuner: probing saa7134[0] i2c adapter [id=0x90000]
i2c-core.o: client [Philips PAL] registered to adapter [saa7134[0]](pos.
0).
saa7134[0]: registered device video0 [???]
saa7134[0]: registered device vbi0
saa7134[0]: registered device radio0
saa7134[0]: registered device dsp2
saa7134[0]: registered device mixer1
saa7134[0]/video: DCSDT: no signal
saa7134[0]/video: DCSDT: found PAL
saa7134[0]/audio: tvaudio thread scan start [1]
saa7134[0]/audio: scanning 5.500 MHz => dc is 0 [0/0]
saa7134[0]/audio: scanning 6.000 MHz => dc is 0 [0/0]
saa7134[0]/audio: scanning 6.500 MHz => dc is 0 [0/0]
saa7134[0]/audio: ctl_mute=0 automute=0 input=Television => mute=0
input=Television
saa7134[0]/audio: found PAL-BGHI main sound carrier @ 0.000 MHz
Next line comes after start radio and stereo-sound is on xawtv.
saa7134[0]/audio: ctl_mute=0 automute=0 input=Radio => mute=0
input=Radio
> Last resort, look at the entry for FlyVideo 2000 in saa7134-cards.c, and
> change the FlyVideo 3000 entry and modify the gpiomask, as well as
> the entry for TV input to use the amux and gpio values from FV2K,
> recompile the saa7134 module and reinstall.
This brings all in confusion, I can't change the channels and the sound
is mono.
Normal compiled saa7134-0.1.6 without any changes:
[procedure]
1.0 Starting xawtv-3.74 with a terminel it display motion pictures but
no
sound. Then starting radio with an other terminel, sound from the
right channel comes up in stereo.
1.2 When I switch channels in xawtv sound don't change with.
1.3 Quit xawtv sound don't quit to.
1.4 Start again xawtv sound goes quit.
1.4.1 Radio is dead, I quit it.
1.6 Select channel MTV in xawtv (this works but no sound).
1.7 Start radio again MTV-sound comes up.
2.0 Radio play not radiostations it play TV-sound.
I hope this describtion is well to understand.
I've read previous discussion in the video4linux-list
concerning the saa7134 driver, this is very specialistic
discussion for me to practise.
