I believe this is the same problem that Franco Catrin L was having on the 27th. When I run xawtv I get only a blue screen for every channel and when I scantv it says no station for everything. I am running RH7.2 with 2.4.18 compiled from source. bttv version is 0.7.91. My log/messages output is here Apr 8 08:27:04 brooke kernel: bttv: driver version 0.7.91 loaded Apr 8 08:27:04 brooke kernel: bttv: using 2 buffers with 2080k (4160k total) for capture Apr 8 08:27:04 brooke kernel: bttv: Host bridge is VIA Technologies, Inc. VT8367 [KT266] Apr 8 08:27:04 brooke kernel: bttv: Bt8xx card found (0). Apr 8 08:27:04 brooke kernel: bttv0: Bt878 (rev 17) at 00:07.0, irq: 18, latency: 64, mmio: 0xddbfe000 Apr 8 08:27:04 brooke kernel: bttv0: using: BT878(Powercolor MTV878/ MTV8) [card=75,insmod option] Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o: Adapter: bt848 #0 scl: 1 sda: 1 -- testing... Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o:1 scl: 1 sda: 0 Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o:2 scl: 1 sda: 1 Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o:3 scl: 0 sda: 1 Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o:4 scl: 1 sda: 1 Apr 8 08:27:04 brooke kernel: i2c-algo-bit.o: bt848 #0 passed test. Apr 8 08:27:04 brooke kernel: i2c-core.o: adapter bt848 #0 registered as adapter 0. Apr 8 08:27:04 brooke kernel: bttv0: i2c: checking for MSP34xx @ 0x80... not found Apr 8 08:27:04 brooke kernel: bttv0: i2c: checking for TDA9875 @ 0xb0... not found Apr 8 08:27:04 brooke kernel: bttv0: i2c: checking for TDA7432 @ 0x8a... not found Apr 8 08:27:04 brooke kernel: i2c-core.o: driver i2c TV tuner driver registered. Apr 8 08:27:04 brooke kernel: tuner: probing bt848 #0 i2c adapter [id=0x10005] Apr 8 08:27:04 brooke kernel: tuner: chip found @ 0xc0 Apr 8 08:27:04 brooke kernel: bttv0: i2c attach [client=Philips NTSC_M (MK2),ok] Apr 8 08:27:04 brooke kernel: i2c-core.o: client [Philips NTSC_M (MK2)] registered to adapter [bt848 #0](pos. 0). Apr 8 08:27:04 brooke kernel: bttv0: registered device video0 Apr 8 08:27:04 brooke kernel: bttv0: registered device vbi0 Apr 8 08:27:04 brooke kernel: bttv0: registered device radio0 Apr 8 08:27:24 brooke kernel: bttv0: PLL: 28636363 => 35468950 ... ok Apr 8 08:27:28 brooke kernel: tuner: TV freq (0.00) out of range (44-958) Apr 8 08:27:28 brooke kernel: bttv0: PLL: switching off The last three lines are repeated everytime I run scantv. This is my modules.conf options ide-cd ignore=hdd alias scd1 sr_mod alias parport_lowlevel parport_pc alias usb-controller usb-uhci alias char-major-195 NVdriver alias eth0 tulip alias sound-slot-0 emu10k1 post-install sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -L >/dev/null 2>&1 || : pre-remove sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -S >/dev/null 2>&1 || : alias char-major-89 i2c-dev options i2c-core i2c_debug=1 options i2c-algo-bit bit_test=1 # bttv alias char-major-81 videodev alias char-major-81-0 bttv options bttv card=75 radio=1 options tuner type=17 debug=0 Do I need to go to development versions or are there options that I can tweak jeb winders winders@xxxxxxxxxxxxxx
