Actually, I did mis-state one tiny thing - My
sysadmin had upgraded it to SCSI-360 when I wasn't looking, darn him. I
discovered that when I pulled the case off to see if there was cache on the
controller. It's Atlas-III/10K and there's 128Meg on the controller.
Internal cache-to-drive-cache speed according to maxtor is 490MByte/sec. I
really have no idea how well implemented their caching system is. But the
results to me suggest that their cache performs better than system cache and
therefore is slowed by allowing caching elsewhere.
For measurement, I use a small application that I
wrote for testing. It's proven time and time again to match all the big
test apps, so I do trust it. The nice thing is that it's small and
lightweight and easy to just run 'real quick' before doing an important video
capture session. Make sure that everything's together.
The winnov board uses a proprietary hardware
compression algorithm that is configurable. I use a 2:1 compression so
that I can get the data onto the drive reliably. At 2:1 there's basically
zero visable loss.
I have a DC30Pro in my Windows machine. Not
at all impressed.
I've ordered a couple of Cheetah 15,000 RPM
SCSI-360 drives.. If you like, I'll report back their results on the same
test.
--- Jodie
----- Original Message -----
Sent: Sunday, July 15, 2001 3:39 PM
Subject: Re: xfs and drive
speeds
Jodie,
OK, you are using high-end(-ish) drives. I find
the un-cached result surprising as it appears to be higher than the result for
the cached test. What are you using to do the test?
Also the very high
cached read result (looks too high to me) would imply that the 512MB of RAM
you have in the machine is having a large effect on the results. Could this be
affecting the write tests also? Does the Adaptec card have a cache?
As
for what you need for capture; I use a DC10+ that does mjpeg compression. At
full resolution it uses 2GB every 5 minutes. This rounds up to 7MB/s. I don't
know about your winnov card, but my DC10+ doesn't do that well on compression
considering what mpeg1 and mpeg2 can do to it.
Anyway, so why such an
interest in this xfs fs format?
Ed-T.
BTW, a single 5K RPM IDE
just isn't good enough, and 7.5K RPMs aren't that much more
expensive.
Jodie Reynolds wrote:
I think Eric has a point. Even with you calculations below, I think the bottleneck is you hard drive. Write rate is slower than read rate. 13MB/s write rate for a single disk is doing very well.
Ed.-T.
I agree Write is slower than Read, but his numbers don't seem all that out of the ball-park, depending on his drive.
testing my video capture box (Dual PIII-1Gig, 512Mb PC133 RAM, dual Quantum Atlas 10,000 RPM drives (one disabled for test) w/29160 Adaptec SCSI-160 controller) I post numbers consistantly higher than 13MB/sec write, actually rather substantially higher, more than double on a long sustained write (like we'd see for video) -
Test File: "/$$test$$.tst" Test File Size: 6400 MB Testing Uncached Write Speed.... Data Transfer: 27.19 MB/s, CPU Load: 0.8% Testing Uncached Read Speed.... Data Transfer: 21.89 MB/s, CPU Load: 0.4% Testing Cached Write Speed.... Data Transfer: 17.89 MB/s, CPU Load: 2.0% Testing Cached Read Speed.... Data Transfer:179.67 MB/s, CPU Load: 0.4% (PHEW!)
I'll also admit that this is skewed some-what out of the park of common consumer machines... !
If we're talking about a 5400 RPM IDE-33 drive, all bets are off. [grin]
But now on to the real question here for a moment: NTSC resolution is what, 480x704 x24bits x30fps (merged-frame/deinterlaced), right?
My numbers for full-screen, merged-frame/uninterlaced, non-hardware assisted capture would then be 480 lines x704 pixels x24 bpp x30 fps or around 238Mbit/sec, which is about 30MBytes/sec, worst-case, right? Which would explain why I like my winnov card doing 2:1 hardware compression taking me down to about 15MByte/sec, or enough to reliably get the data onto the drive.
Did I make some huge mistake here?
--- Jodie Reynolds, CTO Interact Devices, Inc.
_______________________________________________ Video4linux-list mailing list Video4linux-list@xxxxxxxxxx https://listman.redhat.com/mailman/listinfo/video4linux-list
|