kraxel@xxxxxxxxxxxxxxxxxxxxx (Gerd Knorr) writes: > > I have just told Gerd about this hardware change to Hauppauge > > cards so should be support in a future version of the bttv > > driver > > Just released 0.7.46 which has (completely untested) support > for the 44xxx WinTV's. It doesn't seem to do the trick for my model 44354 REV A321 WinTV. I still get nothing but silence from the radio :( This is what happens when I start up "radio" and tune to a station: ,---- | msp34xx: setvolume: 0:0 0x00 0x00 | tuner: tv freq set to 400.00 | msp34xx: setbass: 32768 0x00 | msp34xx: settreble: 32768 0x00 | msp34xx: setvolume: 65535:65535 0x73 0x00 | msp34xx: scart switch: in3 => 0 | msp34xx: setvolume: 65535:65535 0x73 0x00 | msp34xx: setbass: 32768 0x00 | msp34xx: settreble: 32768 0x00 | msp3400: mono setstereo | msp34xx: setvolume: 0:0 0x00 0x00 | tuner: radio freq set to 0.00 | tuner: PLL not locked | tuner: Signal: 8192 | msp34xx: setvolume: 0:0 0x00 0x00 | tuner: radio freq set to 92.62 | tuner: PLL not locked | tuner: Signal: 8192 | msp34xx: setvolume: 0:0 0x00 0x00 | tuner: radio freq set to 400.00 | tuner: PLL not locked | tuner: Signal: 16384 | msp34xx: setvolume: 0:0 0x00 0x00 | tuner: radio freq set to 92.62 | tuner: PLL not locked | tuner: Signal: 24576 `---- Also notice how I need to set the tuner to a high frequency (>= 400 MHz) at least once before the station is properly tuned in. This was mentioned by another poster not long ago. No matter what I do I get no audio from the radio. My mixer settings _are_ correct. Personally, I find the "setvolume: 0:0 0x00 0x00" part a bit suspicious... Just for good measure, this is how my card is detected: ,---- | Linux video capture interface: v1.00 | i2c-algo-bit.o: i2c bit algorithm module | bttv: driver version 0.7.46 loaded | bttv: using 2 buffers with 2080k (4160k total) for capture | bttv: Bt8xx card found (0). | bttv0: Bt878 (rev 17) at 00:0d.0, irq: 11, latency: 32, memory: 0xd9001000 | bttv0: subsystem: 0070:13eb => Hauppauge WinTV => card=10 | bttv0: model: BT878(Hauppauge new (bt878)) [autodetected] | bttv0: Hauppauge msp34xx: reset line init | i2c-core.o: adapter bt848 #0 registered as adapter 1. | bttv0: Hauppauge eeprom: model=44354, tuner=Philips FM1216 (5) | bttv0: i2c: checking for MSP34xx @ 0x80... found | i2c-core.o: driver i2c msp3400 driver registered. | msp34xx: init: chip=MSP3415D-B3, has NICAM support | msp3410: daemon started | bttv0: i2c attach [MSP3415D-B3] | i2c-core.o: client [MSP3415D-B3] registered to adapter [bt848 #0](pos. 0). | msp3410: setting mode: autodetect start (0x0001) | i2c-core.o: driver tv card mixer driver registered. | tvmixer: adapter ISA main adapter | tvmixer: ISA main adapter is not a tv card | tvmixer: adapter bt848 #0 | tvmixer: debug: MSP3415D-B3 | tvmixer: MSP3415D-B3 (bt848 #0) registered with minor 16 | msp3410: detection still in progress | msp3410: detection still in progress | bttv0: i2c: checking for TDA9875 @ 0xb0... not found | bttv0: i2c: checking for TDA7432 @ 0x8a... not found | tvaudio: TV audio decoder + audio/video mux driver | tvaudio: known chips: tda9840,tda9873h,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951) | i2c-core.o: driver generic i2c audio driver registered. | msp3410: current mode: ERROR (0x0000) | msp34xx: setbass: 32768 0x00 | msp34xx: settreble: 32768 0x00 | msp34xx: setvolume: 65535:65535 0x73 0x00 | i2c-core.o: driver i2c TV tuner driver registered. | tuner: chip found @ 0x61 | tuner: type set to 5 (Philips PAL) | bttv0: i2c attach [Philips PAL] | i2c-core.o: client [Philips PAL] registered to adapter [bt848 #0](pos. 1). | bttv0: PLL: 28636363 => 35468950 ... ok `---- Hardware: Hauppauge WinTV/radio PAL (model 44354 REV A321) Software: bttv 0.7.46 radio from xawtv 3.23 kernel 2.2.17 Any ideas? -- Echelon bait: NWO bomb domestic disruption Qaddafi encryption Ruby Ridge Semtex Ft. Knox spy SEAL Team 6 nuclear ECHELON genetic cracking Kibo
